Step 1
Find the measuring position
Place the string around the lower neck, close to the collarbone area.
HERPRESENCE SIZE GUIDE
Find Your Fit
Measure your jewelry size with simple tools before you choose your piece.
Request a Sizing Tape
01
Non-stretch string or paper strip
Use a material that does not stretch.
02
Pen
Mark the point where the ends meet.
03
Ruler
Lay the strip flat and measure in inches.
Choose the jewelry area you want to measure. Each guide opens into a step-by-step visual instruction set.
SIZING TAPE REQUEST
Complete the form below
Share your preferred jewelry category and sizing needs. Selected subscribers may receive a complimentary HERPRESENCE sizing tape.
NECK & NECKLACE SIZE
Measure your neck and preferred necklace length
Keep normal breathing. Do not pull the string tight. Leave two fingers of space if you prefer a relaxed fit.
Step 2
Wrap without squeezing
Keep your head straight. Do not look down, tilt up, or tighten the string.
Step 3
Mark the meeting point
Use a pen to mark where the two ends meet.
Step 4
Measure the string
Lay the string flat and measure from the starting end to the mark. Record the number in inches.
Step 5
Measure your preferred necklace drop
Adjust the string to where you want the necklace to fall, then mark and measure again.
WRIST & BANGLE SIZE
Measure your wrist and palm width
Bracelets, open cuffs, and closed bangles need different measurements. Closed bangles must pass over the widest part of your hand.
Step 1
Find the narrowest wrist area
Usually this is slightly above the wrist bone.
Step 2
Wrap the wrist
Wrap the string around the wrist. It should touch the skin without squeezing.
Step 3
Mark the overlap
Use a pen to mark the point where the string meets.
Step 4
Measure and record
Lay the string flat and measure in inches.
Step 5
For closed bangles, measure the palm
Tuck your thumb in, bring your fingers together, and measure the widest part of your hand.
UPPER ARM SIZE
Measure the full wearing area
For arm cuffs, measure 2–3 positions. The upper arm can be wider near the shoulder and narrower near the elbow.
Step 1
Choose the wearing range
Decide where the arm cuff should sit on your upper arm.
Step 2
Measure the upper point
Let your arm rest naturally. Do not flex, clench, or press your arm against your body.
Step 3
Measure the middle point
Wrap the string around the middle of the intended wearing area without tightening.
Step 4
Measure the lower point
Measure the lower part of the wearing range closer to the elbow.
Step 5
Record all measurements
Write down each number in inches and include the jewelry category when submitting your request.
RING SIZE
Measure your finger circumference
Ring size can change with temperature, swelling, salt intake, and time of day. Measure when your hands feel normal.
Step 1
Choose the finger
Measure the exact finger and position where you want to wear the ring.
Step 2
Wrap the finger
The string should sit against the skin but still move naturally. Do not pull it tight.
Step 3
Mark the meeting point
Use a pen to mark where the string overlaps.
Step 4
Measure the length
Lay the string flat and measure in inches. Repeat 2–3 times for accuracy.
Step 5
Check your knuckle fit
If your knuckle is larger than the base of your finger, an open ring may feel more comfortable.
WAIST CHAIN SIZE
Measure the actual wearing position
Waist chains can sit at the high waist, natural waist, near the navel, or on the hips. Do not choose by pants size only.
Step 1
Choose the wearing position
Decide where you want the waist chain to sit on your body.
Step 2
Wrap horizontally
Stand naturally. Do not suck in, push out, or tighten your waist.
Step 3
Mark the overlap
Use a pen to mark where the string or paper strip meets.
Step 4
Measure flat
Lay the strip flat and measure from the start to the mark. Record in inches.
Step 5
Check while sitting
Sit naturally. If it feels tight when seated, choose the size that feels comfortable sitting down.
ANKLET SIZE
Measure where the anklet will sit
Do not measure only the ankle bone. Anklets move while walking, so avoid a tight fit.
Step 1
Choose the wearing position
Decide whether the anklet will sit higher or lower around the ankle.
Step 2
Wrap naturally
Stand or sit naturally. Do not point your toes or tighten your foot.
Step 3
Mark the overlap
Use a pen to mark where the string meets.
Step 4
Measure and record
Lay the string flat and measure in inches. Choose comfort over tightness.